Wireless Bore to Sump & Sump to Over HeadTank

The Aditya Wireless Auto Changeover Water Level Controller is an advanced intelligent water management system designed to automatically control water transfer between borewell to sump, and Sump to overhead tank.

The system intelligently monitors water levels and automatically operates sump and borewell motors to maintain continuous water supply while protecting pumps from dry run, signal loss, and water flow failures.

Using long-range wireless technology, solar powered tank sensors, and smart safety algorithms, the controller provides a fully automatic and reliable water automation solution for homes, apartments, villas, and commercial buildings.

System Automation Overview

The controller automatically manages the water system in the following sequence:

Borewell to Sump & Sump to Overhead Tank

This ensures:

• Continuous water supply
• No tank overflow
• No pump dry run
• Intelligent motor safety

Automatic Sump to Tank Operation

The overhead tank is monitored using four water level sensing points.

Tank Levels

• 25%
• 50%
• 75%
• 100%

The sump is monitored using three sensing points.

Sump Levels

• Low
• Half
• Full

Working Logic

When the tank water level falls below 50%:

The controller checks the sump water level.

If sufficient water is available, the sump motor starts automatically.

The motor runs until the tank reaches 100% level.

The motor then stops automatically.

Automatic Borewell to Sump Changeover

If the sump becomes empty while filling the tank, the controller performs automatic source changeover.

Changeover Sequence

The controller stops the sump motor.

The borewell motor starts automatically.

Borewell fills the sump until half level.

Borewell motor stops automatically.

The controller restarts the sump motor.

The sump motor continues filling the tank until 100% level.

Why Only Half Sump Filling?

Half of the sump capacity is reserved for municipal water storage, ensuring water availability from external supply sources.

Intelligent Water Flow Detection

The controller verifies actual water flow after motor start.

After motor starts:

• The system checks if water is flowing to the tank.
• If flow is detected, the motor continues running.

A Water Flow LED indicator confirms proper flow.

If No Water Is Detected

If water flow is not detected within 1 minute:

• Motor automatically switches OFF
• Red fault LED turns ON
• Alarm beeps every 10 seconds

This helps detect problems such as:

• Dry borewell
• Air lock in pipeline
• Pipe blockage
• Pump failure

Advanced Dry Run Protection

The system continuously monitors sump water level to prevent pump damage.

If the sump water level becomes insufficient:

• The motor automatically stops immediately

This protects the pump from dry running and overheating.

Power Failure Recovery Protection

When power supply returns after a failure:

• The controller gives a 2-second beep indication.

If tank level is below 50%:

• The system waits 1 minute before starting the motor.

This delay ensures power stability and motor protection.

Manual Water Demand Function

Users can manually request water filling using the NEED Button.

When the NEED button is pressed:

• Motor starts immediately
• Tank fills automatically to 100%
• Motor stops automatically

Visual Motor Operation Indicators

The front panel provides clear motor status indications.

When the motor runs:

• Motor ON LED glows
• Rotating LED indicators show active motor operation

This makes system status easy to understand.

Wireless Technology Architecture

The controller uses long-range wireless communication between:

• Tank sensor unit
• Sump sensor unit
• Main control unit

This eliminates the need for long wiring between tank and motor room.

Installation Benefits

• No wall drilling for cables
• Easy installation
• Neat wiring
• Reliable communication

Solar Powered Tank Sensor

The overhead tank sensor unit is designed for maintenance-free operation.

Features

• High efficiency solar charging system
• EV-grade lithium battery
• Up to 90 days backup without sunlight

Installation Design

• SS304 stainless steel mounting stand
• Fully waterproof enclosure
• Weatherproof antenna

Long Battery Backup for Sump Sensor

The sump sensor unit operates using a dedicated rechargeable battery system.

Backup Performance

• Up to 12 months battery backup after full charge

Smart Battery Monitoring

If battery becomes low:

• Blue low battery LED appears
• Alarm beeps every 30 seconds

The system continues working for 15 additional days, giving time for recharge.

Wireless Signal Monitoring

The controller continuously checks wireless signal status.

Signal Transmission Frequency

Tank Sensor → every 10 seconds

Sump Sensor → every 15 seconds

Signal Loss Protection

If signal is not received within 1 minute:

• Signal loss alert appears
• Alarm beeps every 30 seconds

If signal is lost while the motor is running:

• Motor automatically stops for safety

AI Safety Signal Protection

If wireless communication fails during motor operation:

Controller waits 1 minute.
If signal does not recover:
Motor automatically stops.

This ensures maximum pump safety.

Long Range Wireless Coverage

The system supports long distance wireless communication.

For extended installations:

• Wireless signal repeaters can be used.

For very large buildings or farms:

• Multiple repeaters can be installed.

Repeaters also display tank signal status.

Unique Wireless ID Security

Each controller is programmed with a unique wireless ID.

Advantages:

• Prevents cross communication between nearby systems
• Multiple systems can operate in the same building
• Secure wireless communication

Industrial Grade Electrical Safety

The controller is built with high reliability electrical design.

Safety Features

• High power switching relays
• 5KV isolation transformer
• Shock protection design
• Long life electronic components

Premium Sensor Technology

The system uses industrial grade water sensors.

Sensor Design

• SS316 stainless steel probes
• Food grade plastic housing
• Rust resistant
• Scale resistant
• Long operational life

Easy Installation System

The controller includes a 10-Pin Industrial Green Connector for sensor connections.

Advantages

• No wire tapping required
• Strong secure connections
• Prevents loose contacts
• Reduces malfunction risk

Maintenance & Service Controls

The controller includes service switches for testing and maintenance.

Service Controls

• Dry Run Bypass Switch
• Tank Full Test Switch
• Manual Motor Start Switch

These switches allow easy installation testing and maintenance.

Motor Compatibility

The controller supports:

• Single Phase Motors
• Three Phase Motors

Maximum Capacity

Up to 7.5 HP motor support

Key Highlights

✅ Fully Automatic Water Management
✅ Automatic Borewell to Sump Changeover
✅ Wireless Tank & Sump Sensors
✅ Solar Powered Tank Sensor (90 Day Backup)
✅ Sump Sensor Battery Backup (Up to 12 Months)
✅ Smart Water Flow Detection
✅ Advanced Dry Run Protection
✅ Signal Loss Motor Safety
✅ Unique Wireless ID Communication
✅ Supports Single Phase & Three Phase Motors
✅ Motor Capacity up to 7.5 HP

Perfect Applications

Ideal for:

• Independent houses
• Villas
• Apartments
• Farmhouses
• Commercial buildings
• Industrial water systems

Top of Form

Bottom of Form